UNDERMOUNT SINK BRACKET HD KIT FOR FARMHOUSE SINKS UP TO 400 LBS
$169.99
Discover a durable, professional solution for installing farmhouse, apron-front, and other undermount sinks with the DuraLedge HD Sink Bracket Kit. Designed for straightforward installation and long-term support, the HD kit securely supports a single sink weighing up to 400 lbs when properly installed.
Easy and Durable Installation
Eliminate the need for makeshift 2 x 4 support structures. The DuraLedge HD Sink Bracket Kit provides a clean, durable support system that mounts directly to the cabinet, helping simplify farmhouse and undermount sink installation while preserving valuable space beneath the sink.
Adjustable for Proper Sink Alignment
Sink installations often require precise positioning for proper fit and drainage. DuraLedge HD brackets can be independently adjusted, allowing the installer to position and level the sink during installation while accommodating the specific requirements of the sink and countertop.
Preserve Valuable Cabinet Space
Unlike bulky wood support structures, the DuraLedge HD bracket system mounts to the sides of the cabinet, helping keep the area beneath the sink open for plumbing, disposals, storage, and other fixtures.
Support for Existing Sink Installations
The DuraLedge HD bracket system can also be used in many existing undermount sink installations where additional support or adjustment is needed, provided the brackets can be properly installed within the cabinet.
What’s Included
The DuraLedge HD Sink Bracket Kit includes the hardware needed to install the bracket support system:
- 4 Brackets
- 4 Leg Levelers (4″)
- 12 Machine Screws (2½”x ¼”)
- 12 Washers (1¼” x ¼”)
- 12 Hex Nuts (¼”)
- 12 Split Lockwashers (¼”)
- 4 Pan Head Screws (⅝”)
- 4 Euro Screws (6.3mm x 10mm)
- 4 Hex Nuts (⅜”)
Installing the DuraLedge HD Sink Brackets
Refer to the installation instructions provided below for detailed guidance on proper bracket placement, adjustment, and installation.
Professional Support for Heavy Farmhouse and Undermount Sinks
Choose the DuraLedge HD Sink Bracket Kit for a clean, adjustable, and durable alternative to traditional wood support structures. Designed to support a single farmhouse or undermount sink weighing up to 400 lbs when properly installed.
Add the DuraLedge HD Sink Bracket Kit to your cart below.
Download the instructions here.
Sink Lift sink mount brackets are easy to install. By following our detailed directions below, you’ll discover how quickly mounting your sink can be accomplished.
Tools Needed:
- Sink Manufacture’s Specifications
- Safety Glasses
- Power Drill
- 5/16″ Wood Drill Bit
- #2 Phillips Bit
- 7/16″ Socket or Adjustable Wrench
- 1/4″ Socket or Flat Head Screwdriver (adjust leg leveler)
- Masking Tape For Marking (optional)
- Tape Measure
- Level
- Pencil
Read These Tips
Doing so will ensure a great product. Manufacturer will not be held responsible for damage to any product or other products due to incorrect installation, installation, or negligence.
- Add 3/8″ hex nut to post prior installation and tighten the hex nut against the weld nut after the sink is set. Hex nut goes above the weld nut.
- Finished sink weight not to exceed 400 lbs.
- Weld nuts for adjustable posts must be positioned to the top side of the bracket for proper installation.
- If the sink cabinet has cabinets to be attached to either side, fasten cabinets together prior start of installation.
- Any obstructions in flanking cabinets or appliances must be removed prior drilling. Such as shelving, pull outs, trash pullouts/bins, dishwashers, etc.
- Cabinetry with less than 1/2″ side walls may need reinforcement.
- Any Voids between cabinets must be filled prior installation of bracket bolts going through both walls. Illustration below shows typical voids.
- Brackets must be mounted vertically straight.
- Install leg levelers after brackets have been installed and secured.
- Brackets recommended to be installed a minimum of 3” away from drain(s).
- Split lock washer and hex nut installed against bracket, inside cabinet.
Manual Installation (non-cnc)
- Referencing sink manufactures specifications, note the sink height and depth needed for your specific application.
- Height needed for sink, plus (+) 3” is 3rd hole down from the top of the bracket. Bracket weld nut for adjustable post faces up.
- Fasten brackets using the ⅝” Pan head screw into the 3rd hole down from the top of the bracket.
- Level bracket vertically.
- Mark holes 1, 2, & 4.
- If needed remove bracket and drill holes 1, 2, & 4 with 1/4” drill bit.
- Reinstall bracket using 5/8” Pan Head Screws.
- Finish installing brackets using hardware provided.
- Install leg leveler with 3/8″ hex nut above the weld nut, insert sink and adjust for fit as needed.
- Once the sink is in its final position, move 3/8″ hex nut down to sit snug against the weld nut.